PERC cell technology, due to the rear side passivation, a PERC module can use more red sunlight and the module efficiency increases by up to 1%. Especially in low or diffuse light conditions in the morning or evening hours, PERC modules can achieve better performance; Noble design with silver frame but no warmth or performance reduction due to white backsheets.
Special features
- High-quality A-grade solar cells, higher efficiency thanks to the 210mm cell even in poor lighting conditions
- Surface made of hardened ESG solar glass with a weatherproof coating
- Corrosion-resistant aluminum frame for extended outdoor use with pre-drilled mounting holes
- IP68 junction box with 90cm long 4mm² double-insulated solar cable and MC4 plug
- Integrated bypass diode - minimized drop in performance when shaded
- SGS-TÜV Saar tested according to valid standards
- Guarantee of plus tolerance (0~ + 3%)
- Performance guarantee up to 10 years with 90% and up to 25 years with 80%
- SGS-TÜV Saar tested according to valid standards
- Guarantee of plus tolerance (- + 3%), performance guarantee up to 10 years with 90% and up to 25 years with 80%
- for all needs relating to a self-sufficient and mobile energy supply
Technical data
| Manufacturer model |
Eco Line ES200M36 |
| EAN Code |
4260558574033 |
| Article number |
1100200 |
| Cells |
36 pieces monocrystalline |
| Max. Power (Pm) |
200 W * |
| Max. Voltage (Vmp) |
20.7 V |
| Max. Current (Imp) |
9.67 A |
| Open circuit voltage (Voc) |
24,3V |
| Short circuit current (Isc) |
10,50A |
| Operating temperature |
-40 ° C to +85 ° C |
| Maximum System Voltage |
1000 V DC |
| Power Tolerance |
0~ + 3% |
| Weight |
10,9 kg |
| Dimensions |
1480 * 670 * 30 mm |
- Values according to STC conditions (E = 1000 W / m², Tc = 25 ° C, AM = 1.5)
Product safety information
Manufacturer information:
SolarV GmbH
Am Kronberger Hang 2
Hessen
Schwalbach am Taunus, Deutschland, 65824
info@solarv.de
www.solarv.de
How many bypass diode are installed in solar panel?
Solar panel 10W-80W has one bypass diode; solar panel 100W-320W has two bypass diodes. Exception: 1100100 (100W) has only one diode and 1160105 (XL 100W) has two diodes.
What is the function of the bypass diode?
The bypass diodes’ function is to eliminate the hot-spot phenomena which can damage PV cells and even cause fire if the light hitting the surface of the PV cells in a module is not uniform.
How does shading affect the performance of solar panel?
When solar panels are exposed to shady conditions, their efficiency drops, and their performance suffers as a result. Environmental obstructions such as trees or nearby buildings, clouds, self-shading between panels in parallel rows, dirt, dust, and various other trash such as bird droppings, all cause shading. These shading effects may be static as a result of the obstruction’s location, or dynamic in certain situations, such as a shadow cast by moving clouds. Therefore, eliminating solar shading problems is the most effective way to avoid them.
How can I check the power of my panel?
Measure the open circuit voltage and short circuit current of your solar panel with multimeter and compare the result with the technical data of the panel. Please also note that the calculated values from technical data are ideal values and depend on various factors such as temperature, angle, compass direction, irradiance, air mass, humidity, solar radiation (impairment e.g., by high fog), resistances in cables, connectors, and charge controllers, etc.
Can different solar panels be connected?
Solar panels with the same (or slightly deviated value +/- 1V) voltage (V) but different power (W) can be connected in parallel without any problem.
Solar panels of different voltage and power must not be connected in parallel, because the solar panel with the lowest voltage determines the voltage output of the whole array. When connecting solar panels together in parallel it is important that they ALL have the same nominal voltage value, but it is not necessary that they have the same ampere value.
Solar panels with the same (or slightly deviated value +/- 1A) current (A) but different power (W) can be connected in series without any problem.
Solar panels of different current and power should not be connected in series, because the solar panel with the lowest current determines the current output of the whole array.
In fact, we do not recommend a parallel/series connection of the different solar modules, as a loss of power cannot be avoided in any case.
There are no reviews yet.
